Midsection shortening

Arltralite · **Joined:** August 20th, 2017, 4:34 pm **Posts:** 58

Saw Hevi kevi’s post on a 12” mid section for a 3cyl omc. Very nice work.
Here is the start of my attempt to make a 13.5” (3.5” shorter than a stock short shaft) midsection for a omc 31.8ci engine.

Any suggestions are welcome.
I haven’t figured out what to do with the drive shaft yet. Maybe a floating coupling. Also concerned about the water pump.
One other thought is to have hydraulic or manual lift on the swivel pin.

http://s1250.photobucket.com/user/Arltr ... sort=3&o=5

Arltralite · **Joined:** August 20th, 2017, 4:34 pm **Posts:** 58

Welded up
I think I might do away with the rubber mounts.

http://s1250.photobucket.com/user/Arltr ... 6.jpg.html

LittleCharger · **Joined:** April 1st, 2012, 12:29 am **Posts:** 1445

Arltralite wrote:

Welded up
I think I might do away with the rubber mounts.

http://s1250.photobucket.com/user/Arltr ... 6.jpg.html

can't see your pic use tinypic or something else to upload it, photobucket no longer allows web sharing unless you pay for the service

Hevi Kevi · **Posted:** October 17th, 2017, 12:30 pm

Nice. Looks like you're better at welding that shitty cast aluminum than I am. I have limited experience on aluminum. I never did finish mine up. It's still sitting on the shelf. One of these days...

Arltralite · **Joined:** August 20th, 2017, 4:34 pm **Posts:** 58

The link seems to work for me. Not sure why LittleCharger is having problems.

HeviKevi. Start by putting a ball on your tungsten by setting your machine to dc+ and striking an arc on a piece of copper. Do it any time your electrode gets contaminated. Clean the work well too. Sometimes it’s hard to stay focused and motivated on a project. I hope you finish it.

Arltralite · **Joined:** August 20th, 2017, 4:34 pm **Posts:** 58

Here are some pics of trim indicators. One for tabs and one for the motor. Just made out of lawnmower throttle cables. Will need to add a third, when I finish my hydraulic lift swivel bracket. The top cable is for engine trim and the bottom is for tabs. The zero represents neutral (parallel to the bottom of the boat)

http://i1250.photobucket.com/albums/hh5 ... l3upjl.jpg

http://i1250.photobucket.com/albums/hh5 ... lp98ks.jpg

http://i1250.photobucket.com/albums/hh5 ... vwabw4.jpg

Arltralite · **Joined:** August 20th, 2017, 4:34 pm **Posts:** 58

It’s nice to have a few days off to get back at my projects. Here is a pic of the midsection with some plates welded on to blend the top to the bottom. And an exhaust port.

http://i1250.photobucket.com/albums/hh5 ... dpiwsf.jpg

Hounddog · **Joined:** April 3rd, 2012, 1:52 pm **Posts:** 3162

Another nice mod 30 OMC
http://www.boatracingfacts.com/forums/a ... 1517754423

Arltralite · **Joined:** August 20th, 2017, 4:34 pm **Posts:** 58

Hounddog wrote:

Another nice mod 30 OMC
http://www.boatracingfacts.com/forums/a ... 7&stc=1&d=<a href="tel:1517754423">1517754423</a>

I saw that. A three cylinder. I wonder what the lifespan of those gears is. It would probably be easier to make an adapter for the gear foot to the tower. I may have to try it.
I haven’t worked much on my midsection. I’ve got the winter blues.

Hounddog · **Joined:** April 3rd, 2012, 1:52 pm **Posts:** 3162

I don't remember seeing these motors at this low a price.
https://www.kijiji.ca/v-boat-parts-trai ... nFlag=true

https://www.kijiji.ca/v-powerboat-motor ... nFlag=true

HPBCANADA.COM

Midsection shortening

Who is online