It is currently November 25th, 2024, 5:06 am

Running Rough

View active topics

All times are UTC - 5 hours [ DST ]


Post new topic Reply to topic  [ 10 posts ] 
Author Message
 PostPosted: July 5th, 2014, 12:32 am   
Member
User avatar

Joined: September 12th, 2013, 4:41 pm
Posts: 108
Location: Toronto / Kawarthas
Riddle me this !!

Last weekend my boat wouldn't get on plane. And when it did with my foot to the floor I ran 65mph ( should do 87)... So I brought er back to the dock and did a compression test (perfect) and tossed new plugs in it. Took er out and she ran fine. Problem solved.... I thought

After giving it some more thought this week and talking to a few people I figured it was a fuel issue. Because last year when idling it would just quite on me if I didn't pump the ball or get on the gas...

So! Are you still with me? Pay attention in the back.

Tonight I take er for a ride. Starts and runs mint. 85 up and down. No issues. Did some cruising. Then up on plane. No problem. Then slow down again and it's barely idling and then quits.... Can't get it started. Done. Tow back to dock.

I changed the low pressure fuel pump gadgets etc, new pump ball at the tank, and new fuel filter / water separator. It starts with my foot on the gas but it idles like crap. Rev it up and it sounds great. Take my foot off the gas and it chugs and eventually quits...

Now what??

_________________
2008 Hydrostream Venom W/200merc 2.5
Image


Top
 Profile Send private message  
 PostPosted: July 5th, 2014, 12:49 am   
HPBC PRESIDENT
User avatar

Joined: March 30th, 2012, 2:25 pm
Posts: 2392
Location: Barrie, On
There's 4 blots attaching the clamp to the bobs jack. Unbolt then kick.. Problem solved.


Top
 Profile Send private message  
 PostPosted: July 5th, 2014, 6:57 am   
Team Member
User avatar

Joined: April 1st, 2012, 12:29 am
Posts: 1445
You running aftermarket reeds?

_________________
Bullet 20 cc Super Comp
Delta with a slow 56
Jcraft with a ProV 150


Top
 Profile Send private message  
 PostPosted: July 5th, 2014, 9:21 am   
Member
User avatar

Joined: September 12th, 2013, 4:41 pm
Posts: 108
Location: Toronto / Kawarthas
LittleCharger wrote:
You running aftermarket reeds?


Yes. I had the reeds changed. Dave at aims did them last winter and the motor has been great all summer so far. I do believe he installed carbon fiber reeds, but can't recall the name of them...

_________________
2008 Hydrostream Venom W/200merc 2.5
Image


Top
 Profile Send private message  
 PostPosted: July 5th, 2014, 10:43 am   
Team Member
User avatar

Joined: April 1st, 2012, 12:29 am
Posts: 1445
One potential issue could be a cracked or chipped reed

_________________
Bullet 20 cc Super Comp
Delta with a slow 56
Jcraft with a ProV 150


Top
 Profile Send private message  
 PostPosted: July 5th, 2014, 12:35 pm   
Member
User avatar

Joined: September 12th, 2013, 4:41 pm
Posts: 108
Location: Toronto / Kawarthas
Reeds are good. Also checked fuel pressure. It's good at 45psi. As well as fuel regulator.

Can get the motor running but idles at 500rpm. Need to stay in the gas to keep it going. When I rev it sounds / runs great....

Been on the phone with Dave a lot today haha thanks Dave!

_________________
2008 Hydrostream Venom W/200merc 2.5
Image


Top
 Profile Send private message  
 PostPosted: July 5th, 2014, 1:47 pm   
Team Member

Joined: April 10th, 2012, 1:37 pm
Posts: 290
Location: Dunnville
I'm sure Dave has suggested it on the phone, but how was the fuel when you changed the separator,? did you pour it in a clear glass to see? maybe you could try running a remote tank to eliminate that.
i chipped my reeds a few years back(from a lean sneeze/stalling at idle as i had some water in my fuel) motor ran great but would not idle i had to keep my foot in it to idle and ran like a top off idle still

_________________
#49 Triple C Racing
T750 Delta/ omc


Top
 Profile Send private message  
 PostPosted: July 5th, 2014, 5:59 pm   
Member
User avatar

Joined: September 12th, 2013, 4:41 pm
Posts: 108
Location: Toronto / Kawarthas
Yup! Very possible. I have the gas in a clear jar now waiting. But not seeing much. Boat is going to aim tomorrow. Yay! Boating!

_________________
2008 Hydrostream Venom W/200merc 2.5
Image


Top
 Profile Send private message  
 PostPosted: July 7th, 2014, 1:49 pm   
Member
User avatar

Joined: September 12th, 2013, 4:41 pm
Posts: 108
Location: Toronto / Kawarthas
Whelp! I drove the boat to Aim yesterday and Dave and I hooked er up to the computer and had a look, did some testing etc etc etc for about 3 hours… all while i stood there like an idiot...

Turns out I had an injector stuck open (yes James Cole you were right, all praise the Holy one James Cole).. which subsequently caused my fuel pump to fail. Dave had all the parts on hand to fix the job and install a new injector this morning. Motor is running mint !

I drove my boat to Dave’s shop yesterday….SUNDAY!... and he worked on the bloody thing right then and there. Who does that?? If he has the time he will do anything to accommodate his customers. I can’t say enough good things about working with Dave at Aim Marine. Thanks again Dave.

Thank you HPBC and all those that lent advice. I was deep into that motor on Friday / Sat but just couldn’t find the cure.

Cheers,

_________________
2008 Hydrostream Venom W/200merc 2.5
Image


Top
 Profile Send private message  
 PostPosted: July 7th, 2014, 5:48 pm   
Team Member
User avatar

Joined: April 1st, 2012, 12:29 am
Posts: 1445
Glad to here you are back up and running....Dave is awesome!

_________________
Bullet 20 cc Super Comp
Delta with a slow 56
Jcraft with a ProV 150


Top
 Profile Send private message  
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 10 posts ] 

All times are UTC - 5 hours [ DST ]


Who is online

Users browsing this forum: No registered users and 4 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  


Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group
Style originally created by Volize © 2003 • Redesigned SkyLine by MartectX © 2008 - 2010