Drag plate 2.0

dubber · **Posted:** August 1st, 2013, 5:14 pm

Jeff Yammer wrote:

Good choice as the flexing and harmonics at speed makes the poly susceptible to cracking.

Just out of curiosity, why is polycarbonate more susceptible to cracking then fibre glass in this application?

Jeff Yammer · **Posted:** September 27th, 2013, 4:15 pm

Any to test ???

OneCycle · **Posted:** November 18th, 2013, 5:13 pm

hows this coming along Meechy ?

Supermitchie · **Posted:** November 18th, 2013, 5:26 pm

It will happen this winter at some point. Start up money is an issue. It will happen though.. I have way too much time in the plug.

Anybody seeing mark weigl any time soon? I could send the plug with them to get it gelled. Then I need to sand and buff it.... Then back to mark to get the mould made... For that I want to be present to get a lesson on making them.

OneCycle · **Posted:** November 18th, 2013, 6:08 pm

Supermitchie wrote:

It will happen this winter at some point. Start up money is an issue. It will happen though.. I have way too much time in the plug.

Anybody seeing mark weigl any time soon? I could send the plug with them to get it gelled. Then I need to sand and buff it.... Then back to mark to get the mould made... For that I want to be present to get a lesson on making them.

pre sale for start up cost?

dubber · **Posted:** November 18th, 2013, 10:23 pm

Fine. I am willing to provide you start up costs through a $100 post dated cheque, date of my choosing although it is negotiable, for 75% stake in your company. This deal will not last forever, I cannot stress this enough.

DoktorC · **Posted:** November 18th, 2013, 10:36 pm

dubber wrote:

Fine. I am willing to provide you start up costs through a $100 post dated cheque, date of my choosing although it is negotiable, for 75% stake in your company. This deal will not last forever, I cannot stress this enough.

Well...since dubber is interested...I'm willing to better his offer to $105 but I need a 78% stake in the company. I can only work with 78%..no negotiation.

I would also entertain an offer with dubber...$200 for an even 140% of the company...

dubber · **Posted:** November 19th, 2013, 12:35 am

DoktorC wrote:

dubber wrote:

Fine. I am willing to provide you start up costs through a $100 post dated cheque, date of my choosing although it is negotiable, for 75% stake in your company. This deal will not last forever, I cannot stress this enough.

Well...since dubber is interested...I'm willing to better his offer to $105 but I need a 78% stake in the company. I can only work with 78%..no negotiation.

I would also entertain an offer with dubber...$200 for an even 140% of the company...

Hmm. Very intriguing offer Dok. I would be willing to waive the post dated cheque requirement in light of this offer proposed to go all in with you Dok. Tack on a 25% royalty until we make our money back as well. I say it is a deal pending a review of his company financials.

OneCycle · **Posted:** November 19th, 2013, 10:01 am

I'm willing to beat both offers. with a trade....

I'll give you a 23 pitch aluminum i re pitched to a 27 (Runs Amazing) and a Box of Yamalube with most of the seals broken in exchange for 95% of GBDF and i'll let you call the shots till i dont..

Supermitchie · **Posted:** November 19th, 2013, 11:37 am

OneCycle wrote:

Supermitchie wrote:

It will happen this winter at some point. Start up money is an issue. It will happen though.. I have way too much time in the plug.

Anybody seeing mark weigl any time soon? I could send the plug with them to get it gelled. Then I need to sand and buff it.... Then back to mark to get the mould made... For that I want to be present to get a lesson on making them.

pre sale for start up cost?

After the mold is made... It will probably be this way.

HPBCANADA.COM

Drag plate 2.0

Who is online