| HPBCANADA.COM https://hpbc.ca/ |
|
| Need help identifying this hull https://hpbc.ca/viewtopic.php?f=2&t=1781 |
Page 1 of 2 |
| Author: | hodgify [ November 17th, 2013, 11:41 am ] | ||
| Post subject: | Need help identifying this hull | ||
I have tried a couple different forums to identify this hull ,so far no luck. I am sure it was made in Ontario I have seen one other . Thought it was a Humber Jewel but this has a three point hull not a v bottom. It is 13ft long and 61/2ft wide. I think this hull came from around Huntsville. Any help would be great. In the process of rebuilding and trying to figure how big a motor to put on it.
|
|||
| Author: | Tomcat [ November 17th, 2013, 1:59 pm ] |
| Post subject: | Re: Need help identifying this hull |
Must be a Humber Jewel unless it's a flip. Kid down the street from me has one with a 60 Merc, looks the same. Every one I ever saw (back in the day) had a 35 - 40 Hp Johnny. |
|
| Author: | OneCycle [ November 17th, 2013, 2:10 pm ] |
| Post subject: | Re: Need help identifying this hull |
the lines sure are interesting.... its deff a version of a humber.. cool little boat ! |
|
| Author: | DoktorC [ November 17th, 2013, 2:28 pm ] |
| Post subject: | Re: Need help identifying this hull |
It's a flip of a Humber jewel...with a point added to the bow and some smoothing. The jewel wasn't a vee bottom either...it has a flat area with two strakes on either side. Take a picture of the "pad" area of the hull. |
|
| Author: | hodgify [ November 17th, 2013, 4:54 pm ] | ||
| Post subject: | Re: Need help identifying this hull | ||
The back of this one has been modified to have a V at the back. Was a flat bottom , you can see where the transom was cut down when they added the v . Sent pictures to Humber Boat Company and they told me it is not a Jewel. I have changed the transom to take a long shaft engine , 60 to 75 evinrude.
|
|||
| Author: | hodgify [ November 17th, 2013, 4:56 pm ] | ||
| Post subject: | Re: Need help identifying this hull | ||
Heres a picture showing hull from front.
|
|||
| Author: | Tomcat [ November 17th, 2013, 5:16 pm ] |
| Post subject: | Re: Need help identifying this hull |
What can you say except "Interesting & Unique" |
|
| Author: | DoktorC [ November 17th, 2013, 5:19 pm ] |
| Post subject: | Re: Need help identifying this hull |
Oh shit...no that's not even a copy of a jewel...definitely unique. I haven't seen anything like that before. It'll be cool with a little Stinger or something |
|
| Author: | hodgify [ May 11th, 2014, 8:31 pm ] | ||
| Post subject: | Re: Need help identifying this hull | ||
I have been working on this hull all winter ,was finally able to finish the bottom and get a couple coats of epoxy primer on it ,now that I have it flipped does anybody recognize it now ?
|
|||
| Author: | WalkWithMax [ May 11th, 2014, 9:01 pm ] |
| Post subject: | Re: Need help identifying this hull |
That is like no other hull I have ever seen!!?? The guy that designed it may have had suffered from some prolonged styrene exposure!!??  Great job refinishing it! It will be interesting to hear how it runs! ... its cool to have something that nobody else has.
|
|
| Page 1 of 2 | All times are UTC - 5 hours [ DST ] |
| © 2000, 2002, 2005, 2007 phpBB Group • http://www.phpbb.com | |