HPBCANADA.COM
https://hpbc.ca/

HPDI Programmable Limiter ....
https://hpbc.ca/viewtopic.php?f=19&t=697		 Page 1 of 2
Author:  OneCycle [ November 1st, 2012, 10:32 pm ]
Post subject:  HPDI Programmable Limiter ....
what are the chances this works?

http://www.amazon.com/Programmable-LIMI ... B004W2TGMK
Author:  DoktorC [ November 1st, 2012, 11:29 pm ]
Post subject:  Re: HPDI Programmable Limiter ....
Very unlikely...if Simon can't crack it the eBay guy ain't got much of a chance...

You can't pull a prop to the limiter anyways so what is your concern?
Author:  hcdcanada [ November 2nd, 2012, 7:21 am ]
Post subject:  Re: HPDI Programmable Limiter ....
OneCycle wrote:
what are the chances this works?

http://www.amazon.com/Programmable-LIMI ... B004W2TGMK


i say go for it, that's the same one that apparently works with my motors as well, if it works let me know make sure you put lots of heat to the board when you solder it .
Author:  OneCycle [ November 2nd, 2012, 9:29 am ]
Post subject:  Re: HPDI Programmable Limiter ....
DoktorC wrote:
Very unlikely...if Simon can't crack it the eBay guy ain't got much of a chance...

You can't pull a prop to the limiter anyways so what is your concern?



how much is a new ECU for the HPDI (just in case mine get f'up) ? for $168 buck i feel like i should try it....
Author:  DoktorC [ November 2nd, 2012, 10:12 am ]
Post subject:  Re: HPDI Programmable Limiter ....
$4k probably.....good risk for something you don't need..

By boat runs over 100 without bumping your limiter so....you're probably ok without the solder job..
Author:  OneCycle [ November 2nd, 2012, 10:33 am ]
Post subject:  Re: HPDI Programmable Limiter ....
DoktorC wrote:
$4k probably.....good risk for something you don't need..

By boat runs over 100 without bumping your limiter so....you're probably ok without the solder job..


ok you talked me off the ledge.....
Author:  hcdcanada [ November 2nd, 2012, 11:01 am ]
Post subject:  Re: HPDI Programmable Limiter ....
OneCycle wrote:
DoktorC wrote:
$4k probably.....good risk for something you don't need..

By boat runs over 100 without bumping your limiter so....you're probably ok without the solder job..


ok you talked me off the ledge.....


Don't be a pussy, i would hook 2 of them up wont that double your RPM
Author:  LittleCharger [ November 2nd, 2012, 11:10 am ]
Post subject:  Re: HPDI Programmable Limiter ....
hcdcanada wrote:
OneCycle wrote:
DoktorC wrote:
$4k probably.....good risk for something you don't need..

By boat runs over 100 without bumping your limiter so....you're probably ok without the solder job..


ok you talked me off the ledge.....


Don't be a pussy, i would hook 2 of them up wont that double your RPM


Yup I agree with Todd. You can't let the conservative sweater vest guy talk you off the ledge that quick! :lol:
Author:  OneCycle [ November 5th, 2012, 7:42 pm ]
Post subject:  Re: HPDI Programmable Limiter ....
had lunch with Todd today and he convinced me to double stack these chips.... bring on the rpm....
Author:  OneCycle [ November 6th, 2012, 9:05 am ]
Post subject:  Re: HPDI Programmable Limiter ....
Looks like Simon has figured it out...

http://www.simonmotorsports.com/yamahaecu.html
Page 1 of 2 All times are UTC - 5 hours [ DST ]
© 2000, 2002, 2005, 2007 phpBB Group • http://www.phpbb.com