| HPBCANADA.COM https://hpbc.ca/ |
|
| re-build? i think so..! https://hpbc.ca/viewtopic.php?f=19&t=1524 |
Page 1 of 4 |
| Author: | BoomerMuskoka [ August 14th, 2013, 7:32 pm ] |
| Post subject: | re-build? i think so..! |
   note rod bolt in reed cage,,  rod bolt backed off dumped bearings into cylinder, tadahhhh, rod is a little bent but not in pieces,, ,, question is , do i econo slamb a piston in it and see how long it lasts,, or get 1 new sleeve and over size the rest and put in 6 new pistons and new bearings seals etc. if so how much $$$............... paul? dok? big bore kit 
|
|
| Author: | BoomerMuskoka [ August 15th, 2013, 10:18 am ] |
| Post subject: | Re: re-build? i think so..! |
or maby not , i think this is a 2.4l piston measures 3.350. so its a worn 2.4l right  2.0l is 3.125" 2.5l is 3.5" so is this a chrome bore motor,,  did they make a steel 2.4l  2.4l should be 3.375" how do i tell if its chrome,,, it looks steel to me the other cylinders have hone marks still 
|
|
| Author: | dubber [ August 15th, 2013, 12:06 pm ] |
| Post subject: | Re: re-build? i think so..! |
If the motor was original before this I would imagine that the model or serial number for the unit could be cross referenced to know what type of bore it was (chrome or steel). I cannot tell too much from the photos but if the cylinder walls are damaged in that cylinder I would not put a new piston and rod in to see how long it lasts because I doubt it would be very long. |
|
| Author: | BoomerMuskoka [ August 15th, 2013, 1:25 pm ] |
| Post subject: | Re: re-build? i think so..! |
ODO50584 is the number,, i thought it was a 2.5l steel bore, but its deffinatly a 2.4l judging by the cylinder bore its bang on 3.375 i cant find out if its chrome or steel,, i thought all 2.4s were chrome or nikasil might be mistaken, and i dont think i could save this sleeve anyway, its pretty chewed. pics of the rod and piston,, one rod bolt broke the other backed out, rod cap is mint,, is this the cause? one bolt was in a port the other stuck in the reed cage.. i haven't located the needle barings this is Awesome.     
|
|
| Author: | BoomerMuskoka [ August 15th, 2013, 2:21 pm ] |
| Post subject: | Re: re-build? i think so..! |
steel!!!!! |
|
| Author: | BoomerMuskoka [ August 16th, 2013, 12:54 pm ] |
| Post subject: | Re: re-build? i think so..! |
  the other 5 cylinders have hone marks and are so clean i think this motor had low hours when it popped,, the oil injection was half deleted,, i think the gear is still in it,, so that could be why the rod bolt failed,,also i think it was underpropped and probably spinning way high...       im going to need a reed cage 
|
|
| Author: | BoomerMuskoka [ August 16th, 2013, 4:04 pm ] |
| Post subject: | Re: re-build? i think so..! |
   
|
|
| Author: | Rowboat [ August 17th, 2013, 7:43 am ] |
| Post subject: | Re: re-build? i think so..! |
I have an original 2.4 bp block that has all steel liners. So, yup, they made them. |
|
| Author: | BoomerMuskoka [ August 17th, 2013, 1:30 pm ] |
| Post subject: | Re: re-build? i think so..! |
Rowboat wrote: I have an original 2.4 bp block that has all steel liners. So, yup, they made them. thats what i have here, its steel, i found a 2.4l chrome bore 200 efi that needs 2 pistons, i was going to pickup for parts, but i dont know if i can use any of it,, my other thought was re build it, if was in better condition rod, sleeve and reed cage wise,, |
|
| Author: | BoomerMuskoka [ August 17th, 2013, 4:28 pm ] |
| Post subject: | Re: re-build? i think so..! |
has anyone lifted a power head off a mid by hand? or will i need a lift ring
|
|
| Page 1 of 4 | All times are UTC - 5 hours [ DST ] |
| © 2000, 2002, 2005, 2007 phpBB Group • http://www.phpbb.com | |