| HPBCANADA.COM https://hpbc.ca/ |
|
| 2.6 yami needs some help https://hpbc.ca/viewtopic.php?f=19&t=1172 |
Page 1 of 2 |
| Author: | Northbase [ April 28th, 2013, 10:33 am ] |
| Post subject: | 2.6 yami needs some help |
The early 90's 2.6 200 yami on my mastercraft is due for a little tlc. I'm planning on doing all the regular stuff (plugs, fuel filter etc) but its developed a hard start / intermittent rough idle / occasional stall issue that needs to be dealt with, although the excessive smoke may come in handy in a week or two when the bugs come out. It presents itself as a fuel issue and I was told last year (can't remember by whom) that it could likely be one of the fuel pumps gone bad. This sound like a good place to start and if so what's the best fix? Rebuild or replace? |
|
| Author: | DoktorC [ April 28th, 2013, 10:50 am ] |
| Post subject: | Re: 2.6 yami needs some help |
Does the motor have an actual choke or is it a prime start motor? With respect to the fuel pumps the best way is to replace them. If you choose to rebuild them make sure you have the diaphram tight/stretched/tensioned as it goes together....the pumps are never quite the same after rebuild but it can be done. |
|
| Author: | Northbase [ April 28th, 2013, 2:31 pm ] |
| Post subject: | Re: 2.6 yami needs some help |
It is a choke motor, not a primer. Best to go OEM for the pumps? Between the fuel filter and the oil reservoir on the engine There's a black box with a spring return toggle switch on it. WTF is it and what does it do? |
|
| Author: | dubber [ April 28th, 2013, 7:18 pm ] |
| Post subject: | Re: 2.6 yami needs some help |
That spring return toggle switch is the float override to energize the remote reservoir oil pump I believe. Toggling it should run the remote pump to fill the onboard motor reservoir. Now I will wait for Dok to chastise me on what that switch is  My 2.6 ran like a turd (hard to start, stalled, etc.) until a carb rebuild. |
|
| Author: | LittleCharger [ April 28th, 2013, 7:34 pm ] |
| Post subject: | Re: 2.6 yami needs some help |
I think you toggle the switch to eject the motor off the boat and to the bottom of the lake. 
|
|
| Author: | DoktorC [ April 28th, 2013, 7:40 pm ] |
| Post subject: | Re: 2.6 yami needs some help |
dubber wrote: That spring return toggle switch is the float override to energize the remote reservoir oil pump I believe. Toggling it should run the remote pump to fill the onboard motor reservoir. Now I will wait for Dok to chastise me on what that switch is It's the flux capacitor dumbass!!  Dubber's right...refills the oil tank if you run low...I'd buy an OE pump if it were me... |
|
| Author: | Northbase [ April 28th, 2013, 8:09 pm ] |
| Post subject: | Re: 2.6 yami needs some help |
Is there a carb kit available or do you have to order individual parts? |
|
| Author: | DoktorC [ April 28th, 2013, 8:12 pm ] |
| Post subject: | Re: 2.6 yami needs some help |
Northbase wrote: Is there a carb kit available or do you have to order individual parts? eBay: http://www.ebay.com/itm/YAMAHA-CARBURET ... 87&vxp=mtr |
|
| Author: | Jeff Yammer [ April 28th, 2013, 8:56 pm ] |
| Post subject: | Re: 2.6 yami needs some help |
OEM pump for sure. Or Holley RED. Clean dem carbs too. . |
|
| Author: | Northbase [ April 28th, 2013, 9:14 pm ] |
| Post subject: | Re: 2.6 yami needs some help |
Thanks y'all. Carb kit is ordered, pumps 'll be ordered tomorrow. Letcha know how it turns out. Cheers. |
|
| Page 1 of 2 | All times are UTC - 5 hours [ DST ] |
| © 2000, 2002, 2005, 2007 phpBB Group • http://www.phpbb.com | |