| HPBCANADA.COM https://hpbc.ca/ |
|
| Yamaha Excel 225 lower unit options.? https://hpbc.ca/viewtopic.php?f=19&t=1113 |
Page 1 of 1 |
| Author: | BoomerMuskoka [ April 7th, 2013, 7:31 pm ] |
| Post subject: | Yamaha Excel 225 lower unit options.? |
I'v been looking for a lower upgrade for my excel,, i was thinking of a bob's nose cone,http://www.bobsmachine.com/Products/Nose_Cone_Bigfoot.cfm, either on my case or a new SEI http://www.sterndrive.cc/lowerunits.htm,, but i am wondering if a newer 2.6l v-max lwp unit would fit? and what other options are out there? |
|
| Author: | DoktorC [ April 7th, 2013, 7:51 pm ] |
| Post subject: | Re: Yamaha Excel 225 lower unit options.? |
BoomerMuskoka wrote: I'v been looking for a lower upgrade for my excel,, i was thinking of a bob's nose cone,http://www.bobsmachine.com/Products/Nose_Cone_Bigfoot.cfm, either on my case or a new SEI http://www.sterndrive.cc/lowerunits.htm,, but i am wondering if a newer 2.6l v-max lwp unit would fit? and what other options are out there? I ran a Bob's on mine...worked great. There is no 2.6 LWP vmax case...there is a short in-shore case that does have LWP but they are very rare. Any 2.6 or v4 case will bolt on... |
|
| Author: | BoomerMuskoka [ April 7th, 2013, 8:19 pm ] |
| Post subject: | Re: Yamaha Excel 225 lower unit options.? |
what case should i keep my eye out for? are the v4 cases smaller? or is my best route getting a bobs on mine,,? my concern with that is putting a nose cone on my case and the skeg flying off or something letting go inside,,,i really dont know anything about the lower unit i have other then its old, lol 
|
|
| Author: | DoktorC [ April 7th, 2013, 8:24 pm ] |
| Post subject: | Re: Yamaha Excel 225 lower unit options.? |
I'd check and make sure the skeg is original then put a bobs on it....my 225 is only a year newer than yours...age is no big deal if they're in good shape. |
|
| Author: | BoomerMuskoka [ April 7th, 2013, 10:26 pm ] |
| Post subject: | Re: Yamaha Excel 225 lower unit options.? |
i,ll have to get you too have a look and see what you think,, |
|
| Author: | wildcatt [ April 8th, 2013, 9:45 pm ] |
| Post subject: | Re: Yamaha Excel 225 lower unit options.? |
I put a Bobs dual hose on mine. Worked great. Welded it. Not glued. Tonnes of pressure at hight - even with the standard holes open. I ran both - just in case of weeds. You've got lots to do as it is. Get the whole thing together. Then worry about LWPs LOL One step at a time Grasshopper. |
|
| Author: | BoomerMuskoka [ April 9th, 2013, 9:56 am ] |
| Post subject: | Re: Yamaha Excel 225 lower unit options.? |
wildcatt wrote: I put a Bobs dual hose on mine. Worked great. Welded it. Not glued. Tonnes of pressure at hight - even with the standard holes open. I ran both - just in case of weeds. You've got lots to do as it is. Get the whole thing together. Then worry about LWPs LOL One step at a time Grasshopper. your right iv been all over the map,, lol i shouldn't of started the bow yet either ,, those cracks were looking at me funny so i had to hit them with the grinder,, lol i really can't do much yet i just had surgery jast month on my wrist so im waiting for it to heal up,, so i figure i should round up as many part as i can so once i get working i wont get stuck looking for stuff,, lol i got plywood for the transom yesterday, and called a couple buddys, "i'll grab a case of BEER if they want to come over and help" grind the old transom area clean and ripp out old gauges/steering etc,,, Dok is working on the mid,, foot print gas pedal is in the mail,,, looking for a jack plate,,,, i found bucket seats, trailer and steering,, but its a long drive so im waiting for a nice day for a road tripp, or more local parts....
|
|
| Page 1 of 1 | All times are UTC - 5 hours [ DST ] |
| © 2000, 2002, 2005, 2007 phpBB Group • http://www.phpbb.com | |