It is currently November 25th, 2024, 7:01 am

Yamaha ProV115

 View active topics

Board index » GENERAL » TECH TALK

All times are UTC - 5 hours [ DST ]

Post new topic Reply to topic  Page 1 of 4
  [ 37 posts ]  Go to page 1, 2, 3, 4  Next
  Print view Previous topic | Next topic 
Author Message
DoktorC
 PostPosted: February 28th, 2015, 2:38 pm   
HPBC PRESIDENT
User avatar

Joined: March 31st, 2012, 5:53 pm
Posts: 3548
Location: Lapping lil charger
I finally decided to drag the old girl into the basement where it's warm and make it into something useful. This is going in the 16 DL I bought last winter and will be used on the lake here at the house for dragging the kids around the lake.

I bought the motor from RBT...it was a sinker...so with some JUNK from The Gun I hope it'll be a cheap motor for my kids to wreck lol.

So I started by pulling the sleeves and installing a set of excel sleeves that I scrounged from Boomer

Image

Image

Got the crank and pistons in...I even found a set of new yamaha rings.

Image

Image


Short block all buttoned up...still have to clean the gaskets on the heads but it's getting closer..
Image

Image

_________________
08 SRV w/3.1 Hydro-tec Phase lll

I've got enough torque to tear a hole....in time...

Top
 Profile Send private message  
LittleCharger
 PostPosted: February 28th, 2015, 2:49 pm   
Team Member
User avatar

Joined: April 1st, 2012, 12:29 am
Posts: 1445
Nice dok! That will be a real nice combination. Can't wait to see Mitchie take the first tube run.

_________________
Bullet 20 cc Super Comp
Delta with a slow 56
Jcraft with a ProV 150

Top
 Profile Send private message  
DoktorC
 PostPosted: February 28th, 2015, 2:54 pm   
HPBC PRESIDENT
User avatar

Joined: March 31st, 2012, 5:53 pm
Posts: 3548
Location: Lapping lil charger
LittleCharger wrote:
Nice dok! That will be a real nice combination. Can't wait to see Mitchie take the first tube run.


I'm going to have to check my tripod rating lol.

_________________
08 SRV w/3.1 Hydro-tec Phase lll

I've got enough torque to tear a hole....in time...

Top
 Profile Send private message  
OneCycle
 PostPosted: February 28th, 2015, 8:13 pm   
HPBC PRESIDENT
User avatar

Joined: March 30th, 2012, 2:25 pm
Posts: 2392
Location: Barrie, On
Are excell sleeves diffrent than the stock v4 ones ? Did you do it for performance gains?
Top
 Profile Send private message  
DoktorC
 PostPosted: February 28th, 2015, 8:17 pm   
HPBC PRESIDENT
User avatar

Joined: March 31st, 2012, 5:53 pm
Posts: 3548
Location: Lapping lil charger
OneCycle wrote:
Are excell sleeves diffrent than the stock v4 ones ? Did you do it for performance gains?


Yup :mrgreen:

_________________
08 SRV w/3.1 Hydro-tec Phase lll

I've got enough torque to tear a hole....in time...

Top
 Profile Send private message  
LittleCharger
 PostPosted: March 1st, 2015, 10:18 am   
Team Member
User avatar

Joined: April 1st, 2012, 12:29 am
Posts: 1445
DoktorC wrote:
OneCycle wrote:
Are excell sleeves diffrent than the stock v4 ones ? Did you do it for performance gains?


Yup :mrgreen:


Nothing ever comes out of that shop stock! Cheat'n yamaha guys

_________________
Bullet 20 cc Super Comp
Delta with a slow 56
Jcraft with a ProV 150

Top
 Profile Send private message  
OneCycle
 PostPosted: March 1st, 2015, 10:22 am   
HPBC PRESIDENT
User avatar

Joined: March 30th, 2012, 2:25 pm
Posts: 2392
Location: Barrie, On
LittleCharger wrote:
DoktorC wrote:
OneCycle wrote:
Are excell sleeves diffrent than the stock v4 ones ? Did you do it for performance gains?


Yup :mrgreen:


Nothing ever comes out of that shop stock! Cheat'n yamaha guys



Yeah tell me about it.... Why even modifiy a yamaha... Just buy a merc and start off where the yamaha ends up..... :shock:
Top
 Profile Send private message  
DoktorC
 PostPosted: March 1st, 2015, 10:29 am   
HPBC PRESIDENT
User avatar

Joined: March 31st, 2012, 5:53 pm
Posts: 3548
Location: Lapping lil charger
OneCycle wrote:
LittleCharger wrote:
DoktorC wrote:
OneCycle wrote:
Are excell sleeves diffrent than the stock v4 ones ? Did you do it for performance gains?


Yup :mrgreen:


Nothing ever comes out of that shop stock! Cheat'n yamaha guys



Yeah tell me about it.... Why even modifiy a yamaha... Just buy a merc and start off where the yamaha ends up..... :shock:


My yamaha's never end up in the scrap bin..
:mrgreen:

Some start there though lol

_________________
08 SRV w/3.1 Hydro-tec Phase lll

I've got enough torque to tear a hole....in time...

Top
 Profile Send private message  
BoomerMuskoka
 PostPosted: March 1st, 2015, 9:42 pm   
Member
User avatar

Joined: August 12th, 2012, 8:37 pm
Posts: 2699
Location: lake Muskoka
:lol: looks pretty slick dok, did you have to do any grinding behind the sleeve to match the ports,, i cant wait to see this one go

_________________
Image
89 excel 91 valero,81mph sold
1988 baja x 15, chopped to 13'11" modvp Bridgeport 91mph
19' tempest picklefork 84 mod vpcarb 102mph

Top
 Profile Send private message  
beavertonae-21
 PostPosted: March 2nd, 2015, 9:22 am   
Team Member
User avatar

Joined: April 4th, 2012, 2:04 pm
Posts: 879
Location: Mississauga
looking good Rick. I will have some questions this summer. Going to refresh my Excell one of these days.

_________________
1991 Hydrostream AE-21 2002 OMC modd

Top
 Profile Send private message  
Display posts from previous:  Sort by  
Post new topic Reply to topic  Page 1 of 4
  [ 37 posts ]  Go to page 1, 2, 3, 4  Next

Board index » GENERAL » TECH TALK

All times are UTC - 5 hours [ DST ]

Who is online

Users browsing this forum: Google [Bot] and 8 guests

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  


Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group
Style originally created by Volize © 2003 • Redesigned SkyLine by MartectX © 2008 - 2010