It is currently November 22nd, 2024, 6:56 pm

OMC 56 cubic inch OVAL PORT long block ...$300.00

View active topics

All times are UTC - 5 hours [ DST ]


Post new topic Reply to topic  [ 10 posts ] 
Author Message
 PostPosted: June 21st, 2016, 9:28 am   
Team Member
User avatar

Joined: April 3rd, 2012, 1:52 pm
Posts: 3163
http://www.kijiji.ca/v-boat-parts-trail ... nFlag=true

It has the carbs. I am not sure if the carb size was the same in 1998 for both the 60 and 70. It will have the fine spline crank for sure.


Top
 Profile Send private message  
 PostPosted: June 21st, 2016, 6:33 pm   
Team Member

Joined: May 3rd, 2012, 8:25 pm
Posts: 220
So if they have the same carbs, how did they detune it?


Top
 Profile Send private message  
 PostPosted: June 21st, 2016, 10:38 pm   
Team Member
User avatar

Joined: April 3rd, 2012, 1:52 pm
Posts: 3163
sharpeye Mike wrote:
So if they have the same carbs, how did they detune it?

Most times they just put in smaller jets, use different reed stops and change the timing a few degrees.


Top
 Profile Send private message  
 PostPosted: June 22nd, 2016, 7:50 am   
Member
User avatar

Joined: September 15th, 2015, 2:35 pm
Posts: 392
Location: Slough, England UK
No the above by houndog is wrong.
The oval port specs are nothing at all like the older brdgeports.
The reeds and stops are all the same for all 3 power options for the oval port.. Timing the same for all 3 models too.
Its just the size of the carbs that is the difference.
You will Not make it 70hp without bigger carbs. NO oval port 70hp ever was supposed to be fitted with the 1 inch venturi. ALL 70hp are supposed to have the big carbs.
Please do not confuse this engine with previous models. They are different .
The carbs for the oval port are the black plastic tops.

Any of the 1994 onward 70hp oval port engine bought from new found to have been fitted WRONGLY with the small carbs could have them replaced free of charge under warranty.
This mainly happened on a batch of 1998/9 year engines and 2001 engines.
This is why the myth of same carbs for 60hp & 70hp exists.


Top
 Profile Send private message  
 PostPosted: June 22nd, 2016, 9:49 am   
Team Member
User avatar

Joined: April 3rd, 2012, 1:52 pm
Posts: 3163
According to the parts book the first plastic top carbs appeared as late production carbs for the 60 and 70 hp. 1992 models. The early models had the old carbs. It both cases the difference in the carbs were the jets. 70 hp used 50D jets and 60 hp used 44D jets. We're 1992 motors oval port?


Top
 Profile Send private message  
 PostPosted: June 22nd, 2016, 6:14 pm   
Member
User avatar

Joined: September 15th, 2015, 2:35 pm
Posts: 392
Location: Slough, England UK
Oval port not made in 1992. They did not go into production untill late 93 for the 1994 season.
The pics of my carbs show 1995 60hp and late 1993 70hp carbs. Both black tops and very different at rear of carb for sizes and different venturi.
.


Top
 Profile Send private message  
 PostPosted: June 22nd, 2016, 6:25 pm   
Team Member

Joined: May 3rd, 2012, 8:25 pm
Posts: 220
The head for the 50 horse is also a different part number


Top
 Profile Send private message  
 PostPosted: June 22nd, 2016, 7:05 pm   
Member
User avatar

Joined: September 15th, 2015, 2:35 pm
Posts: 392
Location: Slough, England UK
Yes thats correct mike. I forgot about the 50hp head.


Top
 Profile Send private message  
 PostPosted: June 30th, 2016, 6:21 pm   
Team Member
User avatar

Joined: April 3rd, 2012, 1:52 pm
Posts: 3163
phillnjack wrote:
Oval port not made in 1992. They did not go into production untill late 93 for the 1994 season.
The pics of my carbs show 1995 60hp and late 1993 70hp carbs. Both black tops and very different at rear of carb for sizes and different venturi.
.

According to Boats.net parts listing the same 1992 block was used for the 70 hp in 1993 and 1994??


Top
 Profile Send private message  
 PostPosted: August 2nd, 2016, 12:00 pm   
Member
User avatar

Joined: September 15th, 2015, 2:35 pm
Posts: 392
Location: Slough, England UK
Since when did boats.net get things right ? They don't list the oval port being a 94 engine, and don't list sleeves at all.


Top
 Profile Send private message  
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 10 posts ] 

All times are UTC - 5 hours [ DST ]


Who is online

Users browsing this forum: No registered users and 3 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  


Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group
Style originally created by Volize © 2003 • Redesigned SkyLine by MartectX © 2008 - 2010