It is currently November 22nd, 2024, 5:21 pm

Vision Rebuild

 View active topics

Board index » GENERAL » PROJECT SECTION

All times are UTC - 5 hours [ DST ]

Post new topic Reply to topic  Page 7 of 10
  [ 98 posts ]  Go to page Previous  1 ... 4, 5, 6, 7, 8, 9, 10  Next
  Print view Previous topic | Next topic 
Author Message
beavertonae-21
 PostPosted: May 3rd, 2015, 8:05 pm   
Team Member
User avatar

Joined: April 4th, 2012, 2:04 pm
Posts: 879
Location: Mississauga
looking good. floor looks better than new

_________________
1991 Hydrostream AE-21 2002 OMC modd

Top
 Profile Send private message  
DoktorC
 PostPosted: May 3rd, 2015, 8:35 pm   
HPBC PRESIDENT
User avatar

Joined: March 31st, 2012, 5:53 pm
Posts: 3548
Location: Lapping lil charger
That looks real good.

_________________
08 SRV w/3.1 Hydro-tec Phase lll

I've got enough torque to tear a hole....in time...

Top
 Profile Send private message  
idvette
 PostPosted: May 3rd, 2015, 8:41 pm   
Team Member
User avatar

Joined: October 2nd, 2012, 7:53 am
Posts: 947
Location: Peterborough
Thanks guys. Getting anxious to get this back together now. I was able to procure a new steering setup (thanks rowboat), found 2 leads on jackplates (thanks V8 and 58evinrude) and even a lower unit (thanks Hydroman316). Now all that's left really is a fuel pump & filter, exhaust divider, trim switches, and time to put it all together!

_________________
1988 Canadian Edition Vision sold
1990 Hydrostream Virage Stage 3 Turbo

Top
 Profile Send private message  
Wideopen
 PostPosted: May 3rd, 2015, 10:47 pm   
Member

Joined: June 24th, 2014, 6:58 am
Posts: 116
Location: Corunna ontario
I got a few ex dividers an plates from 2.4s if you need. and a holly red pump. lemmie know if I can help
Top
 Profile Send private message  
BoomerMuskoka
 PostPosted: May 3rd, 2015, 11:09 pm   
Member
User avatar

Joined: August 12th, 2012, 8:37 pm
Posts: 2699
Location: lake Muskoka
get me a pic of your exhaust divider, i dont think its the same as a typical 2.4l.. i might be mistaken but i think yours is a fat block. lets get that thing on the water!! :mrgreen:

_________________
Image
89 excel 91 valero,81mph sold
1988 baja x 15, chopped to 13'11" modvp Bridgeport 91mph
19' tempest picklefork 84 mod vpcarb 102mph

Top
 Profile Send private message  
allstock
 PostPosted: May 4th, 2015, 9:16 am   
Member
User avatar

Joined: August 30th, 2012, 11:21 am
Posts: 325
Do you need a single turn signal trim switch? Pulling mine and installing a double this week.
Top
 Profile Send private message  
idvette
 PostPosted: May 4th, 2015, 12:26 pm   
Team Member
User avatar

Joined: October 2nd, 2012, 7:53 am
Posts: 947
Location: Peterborough
That's what I'm after for now Mike! Boomer I'll get a pic after work, I'm sure I sent you one in the fall

_________________
1988 Canadian Edition Vision sold
1990 Hydrostream Virage Stage 3 Turbo

Top
 Profile Send private message  
idvette
 PostPosted: May 4th, 2015, 6:55 pm   
Team Member
User avatar

Joined: October 2nd, 2012, 7:53 am
Posts: 947
Location: Peterborough
BoomerMuskoka wrote:
get me a pic of your exhaust divider, i dont think its the same as a typical 2.4l.. i might be mistaken but i think yours is a fat block. lets get that thing on the water!! :mrgreen:

Pics sent to your cell boomer. I don't know what constitutes a fat block.....

_________________
1988 Canadian Edition Vision sold
1990 Hydrostream Virage Stage 3 Turbo

Top
 Profile Send private message  
idvette
 PostPosted: May 5th, 2015, 8:49 pm   
Team Member
User avatar

Joined: October 2nd, 2012, 7:53 am
Posts: 947
Location: Peterborough
Wideopen wrote:
I got a few ex dividers an plates from 2.4s if you need. and a holly red pump. lemmie know if I can help

I don't know how I missed this post. Can you send me some pictures of what you have for dividers? And any idea of what pressure the red pump is capable of? I've seen them on carb motors, unsure if they'll work on efi

_________________
1988 Canadian Edition Vision sold
1990 Hydrostream Virage Stage 3 Turbo

Top
 Profile Send private message  
RFCB
 PostPosted: May 5th, 2015, 9:25 pm   
Member
User avatar

Joined: August 7th, 2012, 10:33 pm
Posts: 175
Sean, I have a older Weldon fuel pump that was on the Skater when it had 260's. It is yours if you want it.
Top
 Profile Send private message  
Display posts from previous:  Sort by  
Post new topic Reply to topic  Page 7 of 10
  [ 98 posts ]  Go to page Previous  1 ... 4, 5, 6, 7, 8, 9, 10  Next

Board index » GENERAL » PROJECT SECTION

All times are UTC - 5 hours [ DST ]

Who is online

Users browsing this forum: No registered users and 15 guests

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  


Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group
Style originally created by Volize © 2003 • Redesigned SkyLine by MartectX © 2008 - 2010