HPBCANADA.COM
http://hpbc.ca/

Stringer parts
http://hpbc.ca/viewtopic.php?f=27&t=3547
Page 1 of 2

Author:  TopGun [ October 24th, 2016, 5:18 pm ]
Post subject:  Stringer parts

49 powerhead complete ( needs rebuild) orange 75 hood , pan, mid and some other parts
It was the stuff kevi was selling
$300

Author:  Hounddog [ October 24th, 2016, 7:09 pm ]
Post subject:  Re: Stringer parts

I will take them if they're not already sold. Can pick them up later this week.
Let me know.

Author:  TopGun [ October 25th, 2016, 9:59 am ]
Post subject:  Re: Stringer parts

sure there yours , let me know when you want to get them

Author:  Hounddog [ October 25th, 2016, 12:27 pm ]
Post subject:  Re: Stringer parts

TopGun wrote:
sure there yours , let me know when you want to get them


I will be there Friday at 11 am. Is that OK?

Author:  TopGun [ October 25th, 2016, 6:37 pm ]
Post subject:  Re: Stringer parts

sure that's fine

Author:  voo-doo_child [ October 26th, 2016, 8:41 am ]
Post subject:  Re: Stringer parts

Can I buy the hood?

Author:  Hounddog [ October 26th, 2016, 11:26 am ]
Post subject:  Re: Stringer parts

voo-doo_child wrote:
Can I buy the hood?


Not yet. I plan to FIRST restore the pan, skirt and mid to look as nice as the hood.
Those parts are common whether the motor remains as a 49 or becomes a 56'r.
I'll check the clamp bracket assemble for wear and its overall condition.
I'll remove the head and intake and pull the pistons without disassembling the powerhead.
That will enable me to see inside. I can lube the crank and turn the motor over to check the ignition.
Then I will know what I have to work with.

Author:  Hounddog [ October 27th, 2016, 1:42 pm ]
Post subject:  Re: Stringer parts

NOW, putting this bright orange motor fully restored on this boat! That would be very cool!
http://www.kijiji.ca/v-personal-watercr ... nFlag=true

Author:  tunnelv [ October 27th, 2016, 3:46 pm ]
Post subject:  Re: Stringer parts

Hounddog wrote:
NOW, putting this bright orange motor fully restored on this boat! That would be very cool!
http://www.kijiji.ca/v-personal-watercr ... nFlag=true


Putting that motor in my garage would be cool too !

Author:  Hounddog [ October 28th, 2016, 7:37 pm ]
Post subject:  Re: Stringer parts

Picked up the parts to-day as planned. Thanks Paul.

I got an e-mail from a fellow in Toronto who has a mint original 1976 original short block assembly.
He will sell it for $500.00 which is less cost compared to buying 3 oversize pistons and boring 3 cylinders.
Plus spending several hours reassembling the old powerhead.
Just switch the original carbs, ignition and other stuff over onto the newer one and now it's a nice original powerhead with lots of life.
The motor then becomes a collector piece rather than a refreshed 30 over old race motor.
OR is it better to build a 30 over Jake Elsey 49 race motor.
One step at a time....no rush.

Page 1 of 2 All times are UTC - 5 hours [ DST ]
© 2000, 2002, 2005, 2007 phpBB Group • http://www.phpbb.com