HPBCANADA.COM http://hpbc.ca/ |
|
1988 Charger STV Project http://hpbc.ca/viewtopic.php?f=20&t=3570 |
Page 2 of 8 |
Author: | DoktorC [ November 27th, 2016, 12:05 pm ] |
Post subject: | Re: 1988 Charger STV Project |
Today's "Head" units don't even require a hole. Theres usually a flush mount face but the days of a big hole in the dash are over. Now, like you said there's no real reason for the head unit anymore but they do offer more adjustability and it's less phone handling in a marine environment lol. |
Author: | mistah_max [ November 29th, 2016, 6:10 am ] |
Post subject: | Re: 1988 Charger STV Project |
talonkid wrote: Ya mine was the same way. Floor, stringers and that seat base could basicslly have the water rung out of it like a towel. That being said I don't think 20 mph differences are where it's headed but any speed increase would be awesome yeah speed increase wasnt all related to the rebuilt. but from the first rotten year to the first dry year 10mph was gained with minimal setup change.and it lost 250lbs. the other 10mph was gained with a re-power anf more setup. had a full sound system in mine. cd player and all. now in the talon i went with a pod radio and everything is bluetooth. i use a old cell phone as an mp3player. our actual phones dont risk getting wet |
Author: | talonkid [ December 1st, 2016, 8:22 am ] |
Post subject: | Re: 1988 Charger STV Project |
mistah_max wrote: talonkid wrote: Ya mine was the same way. Floor, stringers and that seat base could basicslly have the water rung out of it like a towel. That being said I don't think 20 mph differences are where it's headed but any speed increase would be awesome yeah speed increase wasnt all related to the rebuilt. but from the first rotten year to the first dry year 10mph was gained with minimal setup change.and it lost 250lbs. the other 10mph was gained with a re-power anf more setup. had a full sound system in mine. cd player and all. now in the talon i went with a pod radio and everything is bluetooth. i use a old cell phone as an mp3player. our actual phones dont risk getting wet That is a ton of weight to be lost. To be honest I could see losing at least 150-200 between the rebuild and rerigging the boat with some better and lighter components. Will have to see what it weighs once its all done. Just about finished up on all the grinding and I'm going to weigh it then before anything else goes back in just to see where it is at. Did you rebuild yours with wood or composite? |
Author: | coffeeguy [ December 8th, 2016, 6:54 am ] |
Post subject: | Re: 1988 Charger STV Project |
I have the same year and color boat and had the same situation earlier this year. Floor soft by the ski pole then I noticed a drip coming out of a chip in the bottom near the rear when on its cradle. Removed the floor and didn't realize there was a sub floor . Figured that out and got lucky when I peeled it off as none of the balsa was glassed to the hull. The seat pedestal was shot(not wet but still shitty). Good luck continued as the sub floor balsa was dry before the bulk head so I didn't need to remove it. The one thing that was poor was the main keel wood(also rotted) was in sections and not bonded to each other. The new piece is made from the Baltic birch and to get the longer length ,finger joined and screwed(I don't know if this is correct but it is better then what was there). I also moved the battery mount from behind the driver to the passenger side.I made the mistake of putting a different prop on the boat when I tried it for the first time after the work was done, but it is a better boat. |
Author: | talonkid [ December 9th, 2016, 1:56 pm ] |
Post subject: | Re: 1988 Charger STV Project |
Ya I first noticed it by the ski pole as well when we went out to go skiing so started getting into it and found the floor and stringers were gone. What did you find in terms of performance difference from the before and after? Do you think it got much lighter? Did you do any bottom work to it? |
Author: | BoomerMuskoka [ December 9th, 2016, 5:51 pm ] |
Post subject: | Re: 1988 Charger STV Project |
did you check the core? |
Author: | talonkid [ December 9th, 2016, 6:34 pm ] |
Post subject: | Re: 1988 Charger STV Project |
Ya, the transom and core are fine. |
Author: | coffeeguy [ December 15th, 2016, 7:26 am ] |
Post subject: | Re: 1988 Charger STV Project |
My core was gone also. I found the boat a bit easier to steer. Probably from using less trim . I think it picked up about 4 mph from 77-81 with the 175 on it. It is a quicker(acceleration) boat with the weight gone. Where it took forever to gain speed above 70 it now pulls well to about 78(64-6500 rpm) and has lots of pull above 5000 |
Page 2 of 8 | All times are UTC - 5 hours [ DST ] |
© 2000, 2002, 2005, 2007 phpBB Group • http://www.phpbb.com |